When Is Custom Silicone Extrusion Tooling Worth It?

Custom silicone extrusion tooling is worth paying for when a bespoke profile solves a fit or assembly problem that an existing section can’t reliably handle, or when the savings over repeat orders recover the upfront cost. If an existing profile already meets the specification, it’s usually the better starting point. The decision comes down to what the finished component must do and what each option costs to buy, fit and support over its working life.

Consider a machinery cover with a seal that operators have to hold in place while lowering the cover. The standard strip may be inexpensive and seal adequately once fitted, but the assembly team spends time repositioning it. A profile that locates in the cover could simplify the job. Before paying for tooling, check whether an existing section can do the same thing and whether the time saved on each build justifies a new die.

Can an existing die produce a suitable profile?

A silicone extrusion die shapes the rubber into a continuous cross-section. A bespoke component doesn’t always require a new die. An existing section might work if the important dimensions, material requirements and fitted behaviour can all be achieved. Silco Products holds nearly 5,000 extrusion dies and can review a drawing or sample to see whether one is suitable. Silco Products Ltd

Start by identifying which features of the profile have to match the assembly. On a retained seal, for example, the width of the locating foot may determine whether the seal stays in its channel. The overall width might have more flexibility if there’s clearance either side. Marking these differences on the drawing gives the manufacturer more scope to find an existing section that works.

Check the alternative in the actual assembly. A profile may look close on a drawing but sit differently at the corners, move during fitting or change the force needed to close a cover. Test it against the same acceptance criteria you’d use for a bespoke part. If both sections meet those criteria, you can compare their costs on equal terms.

What drives the cost of a new silicone extrusion die?

The upfront quote depends on the shape the manufacturer needs to produce and what’s involved in proving the finished profile. A simple section with few critical dimensions gives the manufacturer a different job from a profile with a locating foot, a thin lip and a hollow section that must compress within a defined gap.

Check what the tooling charge includes. One quote might cover the die and initial samples, while another might show them separately. Ask how revisions would be priced if the first sample fits the drawing but the assembly trial shows that the section needs adjusting. That distinction matters when the mating parts are still being developed.

The die is only one part of the cost. The silicone grade, profile size, order quantity and any finishing can all affect the recurring price. Silco can supply cut lengths and can join many extrusions into rings or frame gaskets. If your assembly team needs a finished frame, compare quotes for that finished part. A price per metre leaves cutting, joining and waste to be costed elsewhere. Silco Products Ltd

How do you calculate the tooling payback?

First, compare the recurring cost of each option in the same unit. For a cabinet seal, that might be the cost per fitted door. Include the quoted part price, any cutting or joining done in-house and the fitting time. Add scrap or rework costs if you have enough production data to estimate them. Then divide the extra upfront cost of the bespoke option by the saving per fitted part.

CostExisting profileBespoke profile
Upfront tooling£0£900
Supplied component£3.20£3.60
Preparation and fitting per part£1.40£0.40
Total recurring cost per fitted part£4.60£4.00

In this illustrative example, the bespoke component costs 40p more to buy but saves £1 in preparation and fitting. That gives a net saving of 60p per part. The £900 tooling cost is recovered after 1,500 fitted parts. If you expect to make only 500, you’d recover £300 of that cost over the run. Use actual quote figures and a timed assembly trial to make the calculation for your own project.

Run the numbers against a conservative order forecast as well as the planned quantity. A die that pays back over four repeat batches might still make sense if those batches are committed. If the forecast depends on a product launch or a customer order that hasn’t been placed, check whether the first run alone can justify the cost or whether the decision can wait.

When is tooling worth it for a small production run?

A small run can justify a bespoke die when the shape itself is essential. For example, a replacement seal may need to fit a channel in equipment that’s already built. If available sections either come loose during fitting or prevent the cover from closing properly, the comparison may be between commissioning a profile and modifying the equipment to accept an existing part.

Put a figure against each workable option. What would it cost to alter the channel, remake a cover or fit a separate retainer? Would the change have to be repeated on every machine? A one-off die charge can be easier to justify when it avoids modifying several assemblies, even if the number of seals ordered is small.

Where the equipment design is still changing, an existing profile may be useful for testing the rest of the assembly. If the channel width or closing gap changes during development, wait until the relevant dimensions are stable before committing to production tooling. This reduces the chance of paying for changes to the die after the first fit trial.

What should you check before approving tooling?

  1. Identify the problem the new profile must solve. Record where the existing part falls short, whether that’s retention, assembly time or another measurable issue. Agree how you’ll judge improvement.
  2. Ask the manufacturer to check existing dies. Supply a drawing or sample and highlight the dimensions that govern fit. Explain where the engineering team can accept a different shape or dimension.
  3. Compare costs for the same finished component. Include tooling, samples, cut lengths or joined frames where applicable, plus your own preparation and fitting costs. Use realistic order quantities over the period you expect to run the design.
  4. Agree how the sample will be accepted. Check the sample against the drawing and in the intended assembly before committing to repeat production. Confirm how any changes identified during the trial would affect the quote and schedule.

Frequently asked questions

Does a bespoke silicone profile always require new tooling?

An existing die may already produce a section that meets the application’s requirements. Silco can check your drawing or sample against its existing tooling. The most helpful information is which dimensions and features are essential to the fit and which can vary. Silco Products Ltd

Is there a minimum order quantity that makes tooling worthwhile?

The threshold depends on the upfront cost, the recurring cost difference and the value of solving the assembly problem. If tooling saves money on every fitted part, calculate the break-even quantity. If the profile enables a fit that’s otherwise difficult to achieve, compare it with the cost of adapting the assembly.

Can a new extrusion die be used for repeat orders?

Discuss repeat use when requesting the quote. Ask how the die will be identified for reorders, how changes to the profile would be handled and whether there are any charges associated with storing, maintaining or replacing the tooling. Get the terms in writing if future batches are part of the business case.

Make the decision on the fitted part

Start with a section that meets the functional requirements, then compare the cost of getting it into the assembly. Commission new tooling when the bespoke shape solves a problem you can demonstrate or delivers savings you can measure across a realistic number of orders.

If you’re weighing up an existing section against a bespoke profile, send Silco Products your drawing or sample, the critical fitting dimensions and your expected order quantities. Call 01903 732088 or email sales@silcoproducts.co.uk to discuss the options.